Last Updated on November 10, 2022 by InfraExam

CCNA3 v6.0 Chapter 9 Exam Answers 2018 2019 Full 100%

  1. 1. Question

    What are two reasons for creating an OSPF network with multiple areas? (Choose two.)

  2. 2. Question

    What is used to facilitate hierarchical routing in OSPF?

  3. 3. Question

    Which two statements correctly describe OSPF type 3 LSAs? (Choose two.)

  4. 4. Question
    Which characteristic describes both ABRs and ASBRs that are implemented in a multiarea OSPF network?
  5. 5. Question
    What type of OSPF LSA is originated by ASBR routers to advertise external routes?
  6. 6. Question
    What OSPF LSA type is used to inform routers of the router ID of the DR in each multiaccess network in an OSPF area?
  7. 7. Question

    Refer to the exhibit. Which two statements are correct? (Choose two.)

    CCNA3 v6.0 Chapter 9 Exam 002

    CCNA3 v6.0 Chapter 9 Exam 002

  8. 8. Question
    What routing table descriptor is used to identify OSPF summary networks that originate from an ABR?
  9. 9. Question
    A network administrator is verifying a multi-area OSPF configuration by checking the routing table on a router in area 1. The administrator notices a route to a network that is connected to a router in area 2. Which code appears in front of this route in the routing table within area 1?
  10. 10. Question

    Refer to the exhibit. What can be concluded about network 192.168.4.0 in the R2 routing table?

    CCNA3 v6.0 Chapter 9 Exam 001

    CCNA3 v6.0 Chapter 9 Exam 001

  11. 11. Question
    Which three steps in the design and implementation of a multiarea OSPF network are considered planning steps? (Choose three.)
  12. 12. Question
    Which two networks are part of the summary route 192.168.32.0/22? (Choose two.)
  13. 13. Question

    Refer to the exhibit. What is indicated by the O IA in the router output?

    CCNA3 v6.0 Chapter 9 Exam 004

    CCNA3 v6.0 Chapter 9 Exam 004

  14. 14. Question

    Refer to the exhibit. A network administrator has been asked to summarize the networks shown in the exhibit as part of a multiarea OSPF implementation. All addresses are using a subnet mask of 255.255.255.0. What is the correct summarization for these eight networks?

    CCNA3 v6.0 Chapter 9 Exam 003

    CCNA3 v6.0 Chapter 9 Exam 003

  15. 15. Question
    The network administrator has been asked to summarize the routes for a new OSPF area. The networks to be summarized are 172.16.8.0, 172.16.10.0, and 172.16.12.0 with subnet masks of 255.255.255.0 for each network. Which command should the administrator use to forward the summary route for area 15 into area 0?
  16. 16. Question

    Match each type of OSPF router to its description. (Not all options are used.)

    CCNA3 v6.0 Chapter 9 Exam 01
    CCNA3 v6.0 Chapter 9 Exam 01
  17. 17. Question

    Fill in the blank. Do not use acronyms.
    OSPF type 2 LSA messages are only generated by the     designated      router to advertise routes in multiaccess networks.

  18. 18. Question

    Fill in the blank. Use a number.
    An ASBR generates type              5                 LSAs for each of its external routes and floods them into the area that it is connected to.

  19. 19. Question

    Fill in the blank. Use a number.
    A type           4               LSA identifies the ASBR and provides a route to it.

  20. 20. Question

    Refer to the exhibit. Fill in the blank. Do not use abbreviations.
    The                network 192.168.10.128 0.0.0.127 area 1                  command must be issued to configure R1 for multiarea OSPF.​

    CCNA3 v6.0 Chapter 9 Exam 005

    CCNA3 v6.0 Chapter 9 Exam 005

  21. 21. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
    Why are users in the OSPF network not able to access the Internet?

  22. 22. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
    Fill in the blank. Do not use abbreviations.
    What is the missing command on router R2 to establish an adjacency between routers R1 and R3?   network 172.16.10.0 0.0.0.255 area 0 .