6.1.2 Lab – Implement Single-Area OSPFv2 Answers

• Recommend

Lab – Implement Single-Area OSPFv2 (Answers Version)

Answers Note: Red font color or gray highlights indicate text that appears in the instructor copy only.

Topology

Addressing Table

Objectives

Part 1: Build the Network and Configure Basic Device Settings and Interface Addressing

Part 2: Configure and Verify Single Area OSPF for IPv4 on R1, D1, and D2

Part 3: Configure Default Route Propagation on R1 and Verify the Propagation

Part 4: Implement OSPF Network Optimizing Features

Part 5: DR and BDR Placement

Background / Scenario

In this lab, you will configure single-area OSPF version 2 for IPv4 on a multiaccess Ethernet LAN. This lab was specifically designed to use two Layer 3 switches instead of three routers to highlight how a Layer 3 switch can also be used to provide routing services.

Note: This lab is an exercise in developing, deploying, and verifying how OSPF operates and does not reflect networking best practices.

Note: The router used with CCNP hands-on labs is a Cisco 4221and the two Layer 3 switches are Catalyst 3560 switches. Other Layer 3 switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in the labs.

Note: Make sure that the switches have been erased and have no startup configurations. If you are unsure, contact your instructor.

Answers Note: Refer to the Answers Lab Manual for the procedures to initialize and reload devices.

Required Resources

• 1 Router (Cisco 4221 with Cisco IOS XE Release 16.9.4 universal image or comparable)
• 2 Switches (Cisco 3650 with Cisco IOS XE release 16.9.4 universal image or comparable)
• 1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
• 4 PCs (Windows with terminal emulation program, such as Tera Term)
• Console cables to configure the Cisco IOS devices via the console ports
• Ethernet cables as shown in the topology

Instructions

Part 1:Build the Network and Configure Basic Device Settings and Interface Addressing

In Part 1, you will set up the network topology and configure basic settings and interface addressing on the router and Layer 3 switches.

Note: The Layer 2 switch should only have a default configuration.

Step 1:Cable the network as shown in the topology.

Attach the devices as shown in the topology diagram, and cable as necessary.

Step 2:Configure basic settings for the router and the two Layer 3 switches.

1. Console into each router and Layer 3 switch, enter global configuration mode, and apply the basic settings and interface addressing using the following startup configurations for each device.

Open configuration window

Router R1

hostname R1

no ip domain lookup

line con 0

logging sync

exec-time 0 0

exit

interface Loopback0

ip address 209.165.200.225 255.255.255.224

no shut

exit

interface Loopback1

ip address 192.168.1.1 255.255.255.192

no shut

exit

interface GigabitEthernet0/0/1

ip address 10.10.0.1 255.255.255.248

no shut

exit

Switch D1

hostname D1

no ip domain lookup

line con 0

logging sync

exec-time 0 0

exit

interface g1/0/5

no switchport

ip address 10.10.0.2 255.255.255.248

no shut

exit

interface g1/0/23

no switchport

ip address 10.10.8.1 255.255.255.0

no shut

exit

interface g1/0/24

no switchport

ip address 10.10.9.1 255.255.255.0

no shut

exit

Switch D2

hostname D2

no ip domain lookup

line con 0

logging sync

exec-time 0 0

exit

interface g1/0/5

no switchport

ip address 10.10.0.3 255.255.255.248

no shut

exit

interface g1/0/23

no switchport

ip address 10.10.24.1 255.255.255.0

no shut

exit

interface g1/0/24

no switchport

ip address 10.10.25.1 255.255.255.0

no shut

exit

2. Save the running configuration to startup-config.
3. Verify the interface status using the show ip interface brief command.

R1# show ip interface brief | include manual

GigabitEthernet0/0/110.10.0.1YES manual upup

Loopback0209.165.200.225 YES manual upup

Loopback1192.168.1.1YES manual upup

D1# show ip interface brief | include manual

GigabitEthernet1/0/510.10.0.2YES manual upup

GigabitEthernet1/0/2310.10.8.1YES manual upup

GigabitEthernet1/0/2410.10.9.1YES manual upup

D2# show ip interface brief | include manual

GigabitEthernet1/0/510.10.0.3YES manual upup

GigabitEthernet1/0/2310.10.24.1YES manual upup

GigabitEthernet1/0/2410.10.25.1YES manual upup

4. Verify direct connectivity between the highlighted IP addresses of R1, D1, and D2.

R1# ping 10.10.0.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.0.2, timeout is 2 seconds:

..!!!

Success rate is 60 percent (3/5), round-trip min/avg/max = 2/2/3 ms

R1# ping 10.10.0.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.0.3, timeout is 2 seconds:

..!!!

Success rate is 60 percent (3/5), round-trip min/avg/max = 2/2/3 ms

All three devices should be able to reach the other directly connected networks (i.e., 10.10.0.0/29). Troubleshoot if necessary.

Close configuration window

Part 2:Configure Single-Area OSPFv2

In this part, you will implement single-area OSPF on a multiaccess Ethernet network.

OSPF can be enabled using the traditional network router config command and wildcard mask. The wildcard mask enables the configuration to be as specific or vague as necessary. For example:

• network ip-address 0.0.0.0 area area-id – Configuring the network statement with an IP address explicitly enables OSPF on that interface.
• network network wildcard-mask area area-id – The wildcard mask can explicitly match a subnet, or it can be less specific to match several subnets as required.
• network 0.0.0.0 255.255.255.255 area area-id – This is the vaguest method as the 0.0.0.0 network with 255.255.255.255 wildcard mask matches all enabled interfaces.

An alternate method to using the network router configuration command is to use the interface specific method. Instead of the network statement, an interface is enabled for OSPF using the ip ospf process-id area area-id interface configuration command. Although simpler to use, the disadvantage is that the configuration is not centralized and increases in complexity as the number of interfaces on the routers increases.

Note: There is a newer method to configure OSPF using address families. Address families are covered in OSPFv3 and in CCNP Enterprise: Advanced Routing.

Step 1:Implement OSPF on D1 using Explicit IP addresses.

D1 will advertise its OSPF networks using the OSPF network ip-address 0.0.0.0 area area-id command method and quad-zero wildcard mask. This enables OSPF for Area 0 only on the interfaces that explicitly match the IP addresses configured.

1. Layer 3 switches are not enabled to perform routing by default. Therefore, routing must be enabled using the ip routing global configuration command.

Open configuration window

D1(config)# ip routing

2. Next, enter the OSPF router configuration mode using process ID 123.

D1(config)# router ospf 123

3. When using the quad-zero method, it is not necessary to calculate the actual wildcard mask. You simply advertise the IP address of the interface with a quad-zero wildcard mask and OSPF will advertise using the subnet mask of the interface. Configure OSPF to advertise the network address of the G1/0/5 interface (i.e., 10.10.0.2) with the quad-zero mask.

D1(config-router)# network 10.10.0.2 0.0.0.0 area 0

4. Next, enable OSPF on the G1/0/23 and G1/0/24 interfaces using a quad-zero mask.

D1(config-router)# network 10.10.8.1 0.0.0.0 area 0

D1(config-router)# network 10.10.9.1 0.0.0.0 area 0

These networks are now being advertised to other OSPF routers.

5. Verify the OSPF configuration on D1 using the show ip protocols command.

D1# show ip protocols

*** IP Routing is NSF aware ***

Routing Protocol is “ospf 123“

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Router ID 10.10.9.1

Number of areas in this router is 1. 1 normal 0 stub 0 nssa

Maximum path: 4

Routing for Networks:

10.10.0.2 0.0.0.0 area 0

10.10.8.1 0.0.0.0 area 0

10.10.9.1 0.0.0.0 area 0

Routing Information Sources:

GatewayDistanceLast Update

Distance: (default is 110)

The OSPF router ID chosen was the highest active IPv4 address configured on D1. The Routing for Networks section in the output above confirms that the configured statements are accurately advertising the D1 networks.

Close configuration window

Step 2:Implement OSPF on D2 using Wildcard Masks.

D2 will advertise its OSPF networks using the network router configuration command and wildcard masks.

1. Like D1, D2 must be enabled for routing using the ip routing global configuration command.

Open configuration window

D2(config)# ip routing

2. Next, enter the OSPF router configuration mode using process ID 123. Note that process IDs are only locally significant. Therefore, the process ID of other OSPF routers do not need to match. However, using the same process ID makes it simpler to remember and reduces potential configuration mistakes.

D2(config)# router ospf 123

3. Configure D2 to advertise the g1/0/5 /29 interface in OSPF area 0. The wildcard mask can be calculated using by deducting the subnet mask (i.e., /29 = 255.255.255.248) from 255.255.255.255, resulting in a wildcard mask of 0.0.0.7.

D2(config-router)# network 10.10.0.0 0.0.0.7 area 0

D2(config-router)#

*Mar1 00:16:46.465: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.9.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

Notice the informational message confirming that D2 has established a neighbor relationship with D1 (i.e., 10.10.9.1).

4. Next, configure D2 to advertise the two /24 networks in OSPF area 0. This can be accomplished using two network statements with specific wildcard mask for each subnet.

D2(config-router)# network 10.10.24.0 0.0.0.255 area 0

D2(config-router)# network 10.10.25.0 0.0.0.255 area 0

Note: The two networks could also be enabled using the network 10.10.24.0 0.0.254.255 statement instead.

There are no informational messages this time because these interfaces are not connected to other OSPF–enabled routers. However, these networks are now being advertised to other OSPF routers.

5. Verify the OSPF configuration on D2 using the show ip protocols command.

D2# show ip protocols

*** IP Routing is NSF aware ***

Routing Protocol is “ospf 123“

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Router ID 10.10.25.1

Number of areas in this router is 1. 1 normal 0 stub 0 nssa

Maximum path: 4

Routing for Networks:

10.10.0.0 0.0.0.7 area 0

10.10.24.0 0.0.0.255 area 0

10.10.25.0 0.0.0.255 area 0

Routing on Interfaces Configured Explicitly (Area 0):

Routing Information Sources:

GatewayDistanceLast Update

10.10.9.111000:11:05

Distance: (default is 110)

Again, the OSPF router ID chosen was the highest active IPv4 address configured on D2. The Routing for Networks section confirms that the configured statements are accurately advertising the D2 networks. We now also have another routing information source, 10.10.9.1 (i.e., D1).

Close configuration window

Step 3:Implement OSPF on R1 using the Interface Specific method.

R1 will use the OSPF interface specific method to advertise the Lo1 interface and the G0/0/1 interface. Interface Lo0 will be advertised in Part 3. The interface specific method is simple because there is no need to enter network statements or calculate wildcard masks. You simply enter the ip ospf process-id area area-id interface configuration command on an interface.

Note: Alternatively, the network 0.0.0.0 255.255.255.255 area 0 router configuration command would be simpler. However, it would enable OSPF on all interfaces including the Lo0 interface that will be advertised in Part 3.

1. The loopback interface on R1 is only configured to simulate another network for OSPF to advertise. However, the default behavior of OSPF for loopback interfaces is to advertise a 32-bit host route. To ensure that the /26 network is advertised, the ip ospf network point-to-point interface command must be configured on the loopback 1 interface. Change the network type on the loopback interfaces so that they are advertised with the correct subnet.

Open configuration window

R1(config)# interface loopback 1

R1(config-if)# ip ospf network point-to-point

2. Next enable the loopback interface for OSPF using the ip ospf 123 area 0 command as shown.

R1(config-if)# ip ospf 123 area 0

R1(config-if)# exit

3. Enter interface G0/0/1 and enable it for OSPF.

R1(config)# interface g0/0/1

R1(config-if)# ip ospf 123 area 0

R1(config-if)# end

R1#

R1#

*Dec 22 18:32:48.873: %OSPF-6-DFT_OPT: Protocol timers for fast convergence are Enabled.

R1#

*Dec 22 18:32:49.683: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.9.1 on GigabitEthernet0/0/1 from LOADING to FULL, Loading Done

*Dec 22 18:32:49.683: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.25.1 on GigabitEthernet0/0/1 from LOADING to FULL, Loading Done

*Dec 22 18:32:49.755: %SYS-5-CONFIG_I: Configured from console by console

Notice how the informational messages are confirming that neighbor adjacencies have been established with D1 (i.e., 10.10.9.1) and D2 (i.e., 10.10.25.1).

4. Verify the OSPF configuration on R1 using the show ip protocols command.

R1# show ip protocols | section ospf

Routing Protocol is “ospf 123“

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Router ID 209.165.200.225

Number of areas in this router is 1. 1 normal 0 stub 0 nssa

Maximum path: 4

Routing for Networks:

Routing on Interfaces Configured Explicitly (Area 0):

Loopback1

GigabitEthernet0/0/1

Routing Information Sources:

GatewayDistanceLast Update

10.10.9.111000:03:47

10.10.25.111000:03:47

10.10.25.111000:03:47

Distance: (default is 110)

Again, the router ID chosen is the highest active IPv4 loopback address configured on R1. The Routing for Networks section confirms that routing was explicitly configured on the interfaces. It also displays a new routing source; 10.10.25.1.

Close configuration window

Step 4:Assign Router IDs on R1, D1, and D2.

The OSPF router ID is dynamically assigned in order of preference:

• Manually configured using the router-id router-id router configuration command.
• If it is not manually assigned, then the highest enabled loopback IP address is used as the router ID.
• If there are no loopback interfaces configured, then the highest IP address of any active physical interfaces in the up state becomes the RID when the OSPF process initializes.

It is best to assign a static OSPF router ID for troubleshooting purposes.

To force an existing OSPF network to use the new router IP, the OSPF process must be reset using the clear ip ospf process privileged EXEC command.

1. Assign R1 the router ID 1.1.1.1 as shown.

Open configuration window

R1(config)# router ospf 123

R1(config-router)# router-id 1.1.1.1

% OSPF: Reload or use “clear ip ospf process” command, for this to take effect

R1(config-router)# end

2. Next clear the OSPF process as shown.

R1# clear ip ospf process

Reset ALL OSPF processes? [no]: yes

R1#

*Dec 22 19:10:30.681: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.9.1 on GigabitEthernet0/0/1 from FULL to DOWN, Neighbor Down: Interface down or detached

*Dec 22 19:10:30.681: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.25.1 on GigabitEthernet0/0/1 from FULL to DOWN, Neighbor Down: Interface down or detached

*Dec 22 19:10:30.692: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.9.1 on GigabitEthernet0/0/1 from LOADING to FULL, Loading Done

*Dec 22 19:10:30.692: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.25.1 on GigabitEthernet0/0/1 from LOADING to FULL, Loading Done

3. Confirm that R1 is now using the new router ID as shown.

R1# show ip protocol | include Router ID

Router ID 1.1.1.1

4. Repeat the process on D1 and D2. Use router ID 2.2.2.2 for D1 and 3.3.3.3 for D2. Also confirm that D1 and D2 are using the new router ID.

D1(config)# router ospf 123

D1(config-router)# router-id 2.2.2.2

Reload or use “clear ip ospf process” command, for this to take effect

D1(config-router)# end

D1#

*Mar1 01:34:59.983: %SYS-5-CONFIG_I: Configured from console by console

D1#

D1# clear ip ospf process

Reset ALL OSPF processes? [no]: y

D1#

*Mar1 01:35:13.254: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

*Mar1 01:35:13.254: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.25.1 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

*Mar1 01:35:13.279: %OSPF-5-ADJCHG: Process 123, Nbr 10.10.25.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

*Mar1 01:35:55.121: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D1# show ip protocol | include Router ID

Router ID 2.2.2.2

D2(config)# router ospf 123

D2(config-router)# router-id 3.3.3.3

Reload or use “clear ip ospf process” command, for this to take effect

D2(config-router)# end

D2#

*Mar1 01:38:22.081: %SYS-5-CONFIG_I: Configured from console by console

D2#

D2# clear ip ospf process

Reset ALL OSPF processes? [no]: y

D2#

*Mar1 01:38:29.673: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

*Mar1 01:38:29.673: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

*Mar1 01:38:29.690: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

*Mar1 01:39:10.433: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D2# show ip protocols | include Router ID

Router ID 3.3.3.3

Close configuration window

Step 5:Verify OSPF settings on R1, D1, and D2.

It is imperative to know how to validate that OSPF is operating as configured. The show running-config command only displays the initial OSPF configuration. It does not validate the operation and functionality of OSPF.

Along with the show ip protocols command, there are several other useful OSPF–related show commands to verify that OSPF is operating as expected.

1. The show ip route ospf privileged EXEC command is used to verify the operation of OSPF. The command displays OSPF routes learned with an O, the administrative distance, the assigned metric, the next-hop IP address, and the local exit interface to reach the network.

Open configuration window

R1# show ip route ospf | begin Gateway

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 6 subnets, 3 masks

O10.10.8.0/24 [110/2] via 10.10.0.2, 00:14:49, GigabitEthernet0/0/1

O10.10.9.0/24 [110/2] via 10.10.0.2, 00:14:49, GigabitEthernet0/0/1

O10.10.24.0/24 [110/2] via 10.10.0.3, 00:14:49, GigabitEthernet0/0/1

O10.10.25.0/24 [110/2] via 10.10.0.3, 00:14:49, GigabitEthernet0/0/1

D1# show ip route ospf | begin Gateway

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks

O10.10.24.0/24 [110/2] via 10.10.0.3, 00:15:54, GigabitEthernet1/0/5

O10.10.25.0/24 [110/2] via 10.10.0.3, 00:15:54, GigabitEthernet1/0/5

192.168.1.0/26 is subnetted, 1 subnets

O192.168.1.0 [110/2] via 10.10.0.1, 00:15:54, GigabitEthernet1/0/5

D2# show ip route ospf | begin Gateway

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks

O10.10.8.0/24 [110/2] via 10.10.0.2, 00:16:32, GigabitEthernet1/0/5

O10.10.9.0/24 [110/2] via 10.10.0.2, 00:16:32, GigabitEthernet1/0/5

192.168.1.0/26 is subnetted, 1 subnets

O192.168.1.0 [110/2] via 10.10.0.1, 00:16:32, GigabitEthernet1/0/5

2. Use the show ip ospf interface [brief] command to verify which interfaces are enabled for OSPF, process ID, Area ID, and state. A missing interface could be the result of an incorrect network statement, IP addressing problem, or a disabled interface.

R1# show ip ospf interface brief

InterfacePIDAreaIP Address/MaskCostState Nbrs F/C

Lo11230192.168.1.1/261P2P0/0

Gi0/0/1123010.10.0.1/291DROTH 2/2

D1# show ip ospf interface brief

Interface PIDAreaIP Address/MaskCostState Nbrs F/C

Gi1/0/24123010.10.9.1/241DR0/0

Gi1/0/23123010.10.8.1/241DR0/0

Gi1/0/5123010.10.0.2/291DR2/2

D2# show ip ospf interface brief

InterfacePIDAreaIP Address/MaskCostState Nbrs F/C

Gi1/0/24123010.10.25.1/241DR0/0

Gi1/0/23123010.10.24.1/241DR0/0

Gi1/0/5123010.10.0.3/291BDR2/2

Note: Omitting the “brief” keyword displays detailed information about the OSPF enabled interfaces.

This State field defines the state of the link and can be:

• DR – This is the Designated Router on the multiaccess network (i.e., Ethernet) to which this interface is connected. The DR establishes OSPF adjacencies with all other routers on the network.
• BDR – This is the Backup Designated Router on the multiaccess network to which this interface is connected. Like the DR, the BDR establishes adjacencies with all other routers on the broadcast network.
• DROTH – This is a DROTHER. It is neither the DR nor the BDR on the multiaccess network. All non-DRs and BDRs on the broadcast network would be DROTHERs and establish adjacencies only with the DR and the BDR.
• P2P – This is an OSPF point-to-point interface and does not require a DR or BDR. In this state, the interface is fully functional and starts exchanging hello packets with all of its neighbors.
  3. Use the show ip ospf neighbor [detail] command to verify which OSPF neighbor your device has established adjacencies with, the state, the next-hop IP address, and the exit interface to use. A neighbor may not be appearing include RIDs that are not unique, interconnecting interfaces that are not on a common subnet, MTU values that do not match, Area ID that is not correct, Hello and dead interval timers that do not match, or authentication type / credentials that do not match. The following output confirms that our devices have correctly established adjacencies. The output for R1 is shown below. Repeat the command for D1 and D2.

R1# show ip ospf neighbor

Neighbor IDPriStateDead TimeAddressInterface

2.2.2.21FULL/DR00:00:3310.10.0.2GigabitEthernet0/0/1

3.3.3.31FULL/BDR00:00:3710.10.0.3GigabitEthernet0/0/1

D1# show ip ospf neighbor

Neighbor IDPriStateDead TimeAddressInterface

1.1.1.11FULL/DROTHER00:00:3210.10.0.1GigabitEthernet1/0/5

3.3.3.31FULL/BDR00:00:3410.10.0.3GigabitEthernet1/0/5

D2# show ip ospf neighbor

Neighbor IDPriStateDead TimeAddressInterface

1.1.1.11FULL/DROTHER00:00:3110.10.0.1GigabitEthernet1/0/5

2.2.2.21FULL/DR00:00:3910.10.0.2GigabitEthernet1/0/5

4. Other OSPF validation commands include the show ip ospf, show ip ospf topology-info, show ip ospf database commands. Use these commands now and identify what types of information they generate which may be useful to know when troubleshooting a network.

Close configuration window

Part 3:Configure and Verify the Advertising of a Default Route

In this part, you will configure a default static route to the internet on R1. R1 will then propagate the default route to other OSPF routers as an external Type 2 OSPF route (i.e., O*E2).

Propagating a default is the most efficient method to provide a consistent default gateway to all OSPF– enabled devices.

Step 1:Configure default route advertisement on R1.

1. R1 will be the gateway of last resort for the OSPF internetwork. In our sample topology, the internet is simulated using the Lo0 interface. Configure a static default route out of the Lo0 interface on R1.

Open configuration window

R1(config)# ip route 0.0.0.0 0.0.0.0 lo0

%Default route without gateway, if not a point-to-point interface, may impact performance

Note: Disregard the informational message. In a production environment, a valid physical interface would be used to provide default gateway services.

2. Enter OSPF router configuration mode and use the default-information originate [always] [metric metric-value] [metric-type type-value] command to enable default route propagation. The always keyword advertises a default route even if a static default route does not exist while the route metric and metric type can be changed. R1 is configured to propagate the default route.

R1(config)# router ospf 123

R1(config-router)# default-information originate

R1(config-router)# end

Step 2:Verify the default route advertisement.

1. Verify the routing table on R1.

R1# show ip route static | begin Gateway

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

S*0.0.0.0/0 is directly connected, Loopback0

2. Verify the routing table on D1 and D2.

D1# show ip route | include Gateway|0/0

Gateway of last resort is 10.10.0.1 to network 0.0.0.0

O*E2 0.0.0.0/0 [110/1] via 10.10.0.1, 00:06:55, GigabitEthernet1/0/5

D2# show ip route | include Gateway|0/0

Gateway of last resort is 10.10.0.1 to network 0.0.0.0

O*E2 0.0.0.0/0 [110/1] via 10.10.0.1, 00:09:36, GigabitEthernet1/0/5

Close configuration window

Part 4:Implement OSPF Network Optimizing Features

In this part, you will configure OSPF optimizing features including:

• Passive interfaces
• Link costs
• Reference bandwidth
• Hello and Dead interval timers

Step 1:Configure passive interfaces on R1, D1 and D2.

A passive interface does not send out OSPF messages or process any received OSPF packets. However, the passive interface network segment is still added to the link state database (LSDB) and advertised out of non-passive interfaces. For security reasons, LAN interfaces which are not connected to other OSPF routers should be passive.

There are two approaches to identify passive interfaces.

• Use the passive-interface interface-id router configuration command to make an interface passive. This is a good approach to use when there are only a few interfaces to make passive.
• Use the passive-interface default router config command to make all interfaces passive, and then make some interfaces not passive using the no passive-interface interface-id command. This is a good approach to use when there are many interfaces to make passive, but only a few interfaces that should not be passive.
  1. R1 only needs the Lo1 interface to be passive. The first approach is used to make the Loopback 1 interface passive. Enter OSPF router configuration mode and make the Lo1 interface passive as shown.

Open configuration window

R1(config-if)# router ospf 123

R1(config-router)# passive-interface lo1

R1(config-router)# end

2. Verify which interfaces are passive using the show ip protocols command.

R1# show ip protocols | section ospf

Routing Protocol is “ospf 123″

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Router ID 1.1.1.1

It is an autonomous system boundary router

Redistributing External Routes from,

Number of areas in this router is 1. 1 normal 0 stub 0 nssa

Maximum path: 4

Routing for Networks:

Routing on Interfaces Configured Explicitly (Area 0):

Loopback1

GigabitEthernet0/0/1

Passive Interface(s):

Loopback1

Loopback1

Routing Information Sources:

GatewayDistanceLast Update

3.3.3.311010:45:59

2.2.2.211010:45:59

10.10.9.111010:54:49

10.10.25.111010:49:26

Distance: (default is 110)

3. A Layer 3 switch can potentially have many interfaces that should be passive. For example, assume that D1 and D2 only require their G1/0/5 interface to not be passive. However, all other interfaces should be passive. Using the first approach would be very time-consuming. For this reason, the second approach will be used. All active interfaces will be rendered passive and only interface G1/0/5 will be re-enabled.

D1(config)# router ospf 123

D1(config-router)# passive-interface default

D1(config-router)#

*Mar1 12:30:42.637: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

*Mar1 12:30:42.637: %OSPF-5-ADJCHG: Process 123, Nbr 3.3.3.3 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

D1(config-router)# no passive-interface g1/0/5

D1(config-router)#

*Mar1 12:31:35.880: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D1(config-router)#

*Mar1 12:31:39.445: %OSPF-5-ADJCHG: Process 123, Nbr 3.3.3.3 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D1(config-router)# end

Notice the information messages stating that the OSPF adjacency with R1 and D2 transitioned to the DOWN state. Disabling the passive feature on interface G1/0/5 re-enabled the OSPF adjacency.

4. Repeat the process on D2.

D2(config)# router ospf 123

D2(config-router)# passive-interface default

D2(config-router)#

*Mar1 12:37:05.837: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

*Mar1 12:37:05.837: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Interface down or detached

D2(config-router)# no passive-interface g1/0/5

D2(config-router)#

*Mar1 12:41:12.697: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

*Mar1 12:41:12.706: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D2(config-router)# end

Close configuration window

Step 2:Adjust OSPF link costs.

The OSPF path metric is based on the cumulative interface cost to the network. OSPF assigns the OSPF link cost using the formula Cost = Reference Bandwidth / Interface Bandwidth. The default reference bandwidth is 100 Mbps, therefore, the default formula is Cost = 100,000,000/Interface Bandwidth. For example, a FastEthernet interface would be assigned a cost of 1 (i.e., 100,000,000 / 100,000,000).

However, the default reference bandwidth does not differentiate interfaces faster than FastEthernet. Therefore, OSPF assigns the identical cost of “1”to FastEthernet, Gigabit Ethernet, and 10 GE interfaces.OSPF makes no distinction that the Gig and 10GE interfaces are faster.

Use the auto-cost reference-bandwidth bandwidth-mbps router configuration command to change the reference bandwidth as follows:

• auto-cost reference-bandwidth 100 – Assigns the default reference bandwidth to 100 Mbps which is the default setting. With this setting, FastEthernet = 1, GigabitEthernet = 1, and 10GE = 1.
• auto-cost reference-bandwidth 1000 – Assigns the default reference bandwidth to 1 Gbps. With this setting, FastEthernet = 10, GigabitEthernet = 1, and 10GE = 1.
• auto-cost reference-bandwidth 10000 – Assigns the default reference bandwidth to 10 Gbps. With this setting, FastEthernet = 100, GigabitEthernet = 10, and 10GE = 1.

Note: The auto-cost reference-bandwidth must be the same on all routers in the area. Otherwise suboptimal routing may occur.

1. On R1, change the reference bandwidth to account for the Gigabit interfaces as shown.

Open configuration window

R1(config)# router ospf 123

R1(config-router)# auto-cost reference-bandwidth 1000

% OSPF: Reference bandwidth is changed.

Please ensure reference bandwidth is consistent across all routers.

R1(config-router)# end

2. Verify that the reference bandwidth has changed to account for the Gigabit interfaces using the show ip ospf command.

R1# show ip ospf | include Ref

Reference bandwidth unit is 1000 mbps

3. Repeat the steps on D1 and D2 to change the reference bandwidth to account for the Gigabit interfaces.

D1(config)# router ospf 123

D1(config-router)# auto-cost reference-bandwidth 1000

% OSPF: Reference bandwidth is changed.

Please ensure reference bandwidth is consistent across all routers.

D1(config-router)# end

D1# show ip ospf | include Ref

Reference bandwidth unit is 1000 mbps

D2(config)# router ospf 123

D2(config-router)# auto-cost reference-bandwidth 1000

% OSPF: Reference bandwidth is changed.

Please ensure reference bandwidth is consistent across all routers.

D2(config-router)# end

D2# show ip ospf | include Ref

Reference bandwidth unit is 1000 mbps

4. Verify the routing table on D2 to see if the route metrics have increased.

R1# show ip route ospf | begin Gateway

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

10.0.0.0/8 is variably subnetted, 6 subnets, 3 masks

O10.10.8.0/24 [110/20] via 10.10.0.2, 00:05:57, GigabitEthernet0/0/1

O10.10.9.0/24 [110/20] via 10.10.0.2, 00:05:57, GigabitEthernet0/0/1

O10.10.24.0/24 [110/20] via 10.10.0.3, 00:03:31, GigabitEthernet0/0/1

O10.10.25.0/24 [110/20] via 10.10.0.3, 00:03:31, GigabitEthernet0/0/1

D1# show ip route ospf | begin Gateway

Gateway of last resort is 10.10.0.1 to network 0.0.0.0

10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks

O10.10.24.0/24 [110/20] via 10.10.0.3, 00:02:48, GigabitEthernet1/0/5

O10.10.25.0/24 [110/20] via 10.10.0.3, 00:02:48, GigabitEthernet1/0/5

192.168.1.0/26 is subnetted, 1 subnets

O192.168.1.0 [110/11] via 10.10.0.1, 00:02:48, GigabitEthernet1/0/5

O*E2 0.0.0.0/0 [110/1] via 10.10.0.1, 00:02:48, GigabitEthernet1/0/5

D2# show ip route ospf | begin Gateway

Gateway of last resort is 10.10.0.1 to network 0.0.0.0

10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks

O10.10.8.0/24 [110/20] via 10.10.0.2, 00:00:10, GigabitEthernet1/0/5

O10.10.9.0/24 [110/20] via 10.10.0.2, 00:00:10, GigabitEthernet1/0/5

192.168.1.0/26 is subnetted, 1 subnets

O192.168.1.0 [110/11] via 10.10.0.1, 00:00:10, GigabitEthernet1/0/5

O*E2 0.0.0.0/0 [110/1] via 10.10.0.1, 00:00:10, GigabitEthernet1/0/5

Close configuration window

Step 3:Alter Hello and Dead interval timers.

OSPF Hello messages are exchanged to establish a neighbor relationship and to ensure that adjacent OSPF neighbors are still available. OSPF uses a hello timer and a dead interval timer which is four times the hello timer.

When a router receives a Hello packet, the dead interval resets and starts to decrement again. If subsequent hello packets are not received before the OSPF dead interval timer reaches 0, the neighbor state is changed to down. The router then sends out the appropriate topology change LSA to all other peers and the SPF algorithm must be recalculated on all routers in the area.

The default OSPF hello timer interval varies based on the OSPF network type. On broadcast and point-to-point links, the default hello timer interval is 10 seconds and dead timer interval is 40 seconds. On non-broadcast multiaccess (NBMA) and point-to-multipoint networks, the default hello interval is 30 seconds with a dead timer interval of 120 seconds.

You can alter the hello timer interval with values between 1 and 65,535 seconds using the ip ospf hello-interval seconds interface configuration command.

The dead interval can be modified using the ip ospf dead-interval seconds interface configuration command. However, the command is really not required because changing the hello timer interval automatically modifies the default dead interval.

1. On R1, change the hello interval on the G0/0/1 interface to 5 seconds and a dead interval time to 20 seconds.

Open configuration window

R1(config)# interface g0/0/1

R1(config-if)# ip ospf hello-interval 5

R1(config-if)# ip ospf dead-interval 20

R1(config-if)# end

*Dec 23 08:52:07.961: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet0/0/1 from FULL to DOWN, Neighbor Down: Dead timer expired

*Dec 23 08:52:30.471: %OSPF-5-ADJCHG: Process 123, Nbr 3.3.3.3 on GigabitEthernet0/0/1 from FULL to DOWN, Neighbor Down: Dead timer expired

Notice how R1 has received OSPF adjacency change messages for D1 and D2. The reason is because OSPF timers must match between interconnecting peers. Therefore, the D1 and D2 GigabitEthernet1/0/5 interface must also be configured with the identical timers.

2. Verify that the timers have changed on G0/0/1 using the show ip ospf interface command.

R1# show ip ospf interface g0/0/1 | include Timer

Timer intervals configured, Hello 5, Dead 20, Wait 20, Retransmit 5

3. Configure D1 with the identical hello and dead interval timers on GigabitEthernet1/0/5 and verify.

*Mar1 15:12:45.159: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet0/5 from FULL to DOWN, Neighbor Down: Dead timer expired

D1(config)# interface g1/0/5

D1(config-if)# ip ospf hello-interval 5

D1(config-if)# ip ospf dead-interval 20

D1(config-if)#

*Mar1 15:18:25.779: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D1(config-if)# end

D1#

*Mar1 15:18:53.201: %OSPF-5-ADJCHG: Process 123, Nbr 3.3.3.3 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Dead timer expired

D1# show ip ospf interface g1/0/5 | include Timer

Timer intervals configured, Hello 5, Dead 20, Wait 20, Retransmit 5

Notice the first OSPF adjacency change message indicating that D1 had lost adjacency with R1. After the commands are entered, the next OSPF adjacency change message indicates that the adjacency with R1 has been re-established. However, the second adjacency change message indicates that the adjacency with D2 has been lost because its timers are not matching.

Also notice that the dead interval was automatically adjusted without having to configure the ip ospf dead-interval 20 command on the interface.

4. Configure D2 with the identical hello and dead interval timers on GigabitEthernet1/0/5 and verify.

*Mar1 15:12:34.045: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Dead timer expired

*Mar1 15:19:24.717: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from FULL to DOWN, Neighbor Down: Dead timer expired

D2#

D2# conf t

D2(config)# interface g1/0/5

D2(config-if)# ip ospf hello-interval 5

D2(config-if)# ip ospf dead-interval 20

*Mar1 15:38:48.158: %OSPF-5-ADJCHG: Process 123, Nbr 1.1.1.1 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

*Mar1 15:38:52.965: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D2(config-if)# end

D2# show ip ospf interface g1/0/5 | include Timer

Timer intervals configured, Hello 5, Dead 20, Wait 20, Retransmit 5

Close configuration window

Again, notice the existing OSPF adjacency change messages indicating that D2 had lost adjacency with R1 and D1.

After the commands are entered, the next OSPF adjacency change messages indicate adjacencies with R1 and D1 have been re-established. And again, the dead interval was automatically adjusted without having to configure the ip ospf dead-interval 20 command on the interface.

Part 5:DR and BDR Placement

In this part, you will configure OSPF DR and BDR placement on the multiaccess network.

By default, an OSPF router tries to establish neighbor adjacencies with all other OSPF routers. This is a concern with large multiaccess (i.e. Ethernet) networks. For instance, 10 routers interconnected to the same Layer 2 switch would require a total of 45 adjacencies to be established. This can cause excessive OSPF traffic and waste router resources.

For this reason, OSPF routers interconnected to the same multiaccess network elect a designated router (DR) and a backup designated router (BDR). All non-DR and BDR routers are referred to as DROTHERS and only form adjacencies with DR and BDR routers. This reduces the total number of adjacencies and improves network operations.

DR and BDR are automatically elected during the last phase of the 2-Way OSPF neighbor state, before the ExStart state.

DR and BDR elections are conducted as follows:

1)An OSPF router interface with a priority greater than 0 attempts to become BDR on the link.

2)If no BDR exists, then it elects itself the BDR. If there is a tie with another router, the highest router ID is used.

3)If there is no DR, the BDR promotes itself as DR.

4)The neighbor with the next highest priority is elected BDR.

The DR and BDR are the central focal points on a multiaccess network. In a large network, it is advantageous to choose which router should be DR and BDR.

When all OSPF routers have the same OSPF priority, the election is based on the higher router ID. Altering router ID to choose DR/BDR routers may not be convenient. A better alternative is to alter the interface priority.

By default, all OSPF routers on a multiaccess network have a priority of 1 assigned. An interface priority can be changed using the ip ospf priority value interface configuration command. The value can be between 0 and 255. Setting the value to 0 ensures the router will never become a DR or BDR. Setting the value greater than the default value of 1, makes the router a candidate to become the DR or BDR.

Note: It may be necessary to use the clear ip ospf process to ensure the proper devices are elected.

Step 1:Verify current DR and BDR selection.

In the topology, R1, D1, and D2 are interconnected on the same Ethernet network. Therefore, a DR/BDR election has already transpired. The easiest way to determine the interface role is by viewing the OSPF interface with the show ip ospf neighbor command.

1. On R1, verify the current DR/BDR status using the show ip ospf neighbor command.

Open configuration window

R1# show ip ospf neighbor

Neighbor IDPriStateDead TimeAddressInterface

2.2.2.21FULL/DROTHER00:00:1910.10.0.2GigabitEthernet0/0/1

3.3.3.31FULL/DR00:00:1810.10.0.3GigabitEthernet0/0/1

From the perspective of R1, D1 (i.e., 2.2.2.2) is a DROTHER and D2 (i.e., router ID 3.3.3.3) is the DR. We must then assume that R1 is the BDR.

2. Verify the current status of R1 using the show ip ospf interface G0/0/1 command.

R1# show ip ospf interface g0/0/1

GigabitEthernet0/0/1 is up, line protocol is up

Internet Address 10.10.0.1/29, Interface ID 7, Area 0

Attached via Interface Enable

Process ID 123, Router ID 1.1.1.1, Network Type BROADCAST, Cost: 10

Topology-MTIDCostDisabledShutdownTopology Name

010nonoBase

Enabled by interface config, including secondary ip addresses

Transmit Delay is 1 sec, State BDR, Priority 1

Designated Router (ID) 3.3.3.3, Interface address 10.10.0.3

Backup Designated router (ID) 1.1.1.1, Interface address 10.10.0.1

Timer intervals configured, Hello 5, Dead 20, Wait 20, Retransmit 5

oob-resync timeout 40

Hello due in 00:00:02

Supports Link-local Signaling (LLS)

Cisco NSF helper support enabled

IETF NSF helper support enabled

Can be protected by per-prefix Loop-Free FastReroute

Can be used for per-prefix Loop-Free FastReroute repair paths

Not Protected by per-prefix TI-LFA

Index 1/2/2, flood queue length 0

Next 0x0(0)/0x0(0)/0x0(0)

Last flood scan length is 1, maximum is 2

Last flood scan time is 0 msec, maximum is 1 msec

Neighbor Count is 2, Adjacent neighbor count is 2

Adjacent with neighbor 2.2.2.2

Adjacent with neighbor 3.3.3.3(Designated Router)

Suppress hello for 0 neighbor(s)

The output confirms that R1 is the BDR and that D2 (i.e., 3.3.3.3) is the DR.

3. Verify the current DR/BDR status on D1 and D2 using the show ip ospf neighbor command.

Close configuration window

Step 2:Change DR and BDR selection.

It is sometimes advantageous to choose which router is selected as DR and BDR. For example, we will change the DR and BDR assignment as follows:

• R1 is currently the BDR but should be the DR using a priority of 255.
• D1 is currently a DROTHER but should be the BDR using the default priority.
• D2 is currently DR but should never become DR or BDR using a priority of 0.
  1. Starting on D2, enter interface G1/0/5 and set the priority to 0 as shown.

Open configuration window

D2(config)# interface g1/0/5

D2(config-if)# ip ospf priority 0

D2(config-if)#

*Mar1 17:23:20.195: %OSPF-5-ADJCHG: Process 123, Nbr 2.2.2.2 on GigabitEthernet1/0/5 from LOADING to FULL, Loading Done

D2(config-if)# end

Notice the OSPF message. The reason is because D1 (i.e., 2.2.2.2) just assumed either the DR or BDR role and has established an adjacency with D2.

2. Verify the current DR / BDR placement.

D2# show ip ospf neighbor

Neighbor IDPriStateDead TimeAddressInterface

1.1.1.11FULL/DR00:00:1810.10.0.1GigabitEthernet1/0/5

2.2.2.21FULL/BDR00:00:1810.10.0.2GigabitEthernet1/0/5

The output confirms that R1 (i.e., 1.1.1.1) is now the DR and D1 (i.e., 2.2.2.2) is the BDR.

The reason R1 became the DR is because it had already been elected as BDR. When a DR fails, the elected BDR is automatically elected as DR to avoid network instability.

3. Although R1 is already the DR, change the interface priority to ensure it is always a candidate to be DR.

R1(config)# interface g0/0/1

R1(config-if)# ip ospf priority 255

R1(config-if)# end

4. Verify that R1 is now the DR.

R1# show ip ospf interface g0/0/1 | include State

Transmit Delay is 1 sec, State DR, Priority 255

5. Verify the roles of D1 and D2.

R1# show ip ospf neighbor

Neighbor IDPriStateDead TimeAddressInterface

2.2.2.21FULL/BDR00:00:1910.10.0.2GigabitEthernet0/0/1

3.3.3.30FULL/DROTHER00:00:1510.10.0.3GigabitEthernet0/0/1

Close configuration window

Router Interface Summary Table

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.

End of document

Device Configs – Final

Router R1

R1# show run

Building configuration…

Current configuration : 4260 bytes

!

version 16.9

service timestamps debug datetime msec

service timestamps log datetime msec

platform qfp utilization monitor load 80

no platform punt-keepalive disable-kernel-core

!

hostname R1

!

boot-start-marker

boot-end-marker

!

no aaa new-model

!

no ip domain lookup

!

login on-success log

!

subscriber templating

!

multilink bundle-name authenticated

!

spanning-tree extend system-id

!

redundancy

mode none

!

interface Loopback0

ip address 209.165.200.225 255.255.255.224

!

interface Loopback1

ip address 192.168.1.1 255.255.255.192

ip ospf network point-to-point

ip ospf 123 area 0

!

interface GigabitEthernet0/0/0

no ip address

shutdown

negotiation auto

!

interface GigabitEthernet0/0/1

ip address 10.10.0.1 255.255.255.248

ip ospf dead-interval 20

ip ospf hello-interval 5

ip ospf priority 255

ip ospf 123 area 0

negotiation auto

!

router ospf 123

router-id 1.1.1.1

auto-cost reference-bandwidth 1000

passive-interface Loopback1

default-information originate

!

ip forward-protocol nd

no ip http server

ip http authentication local

ip http secure-server

ip route 0.0.0.0 0.0.0.0 Loopback0

!

banner motd ^C This is R1, Implement Single-Area OSPFv2 Lab ^C

!

line con 0

exec-timeout 0 0

logging synchronous

transport input none

stopbits 1

line aux 0

stopbits 1

line vty 0 4

login

!

end

Switch D1

D1# show run

Building configuration…

Current configuration : 6646 bytes

!

version 16.9

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

! Call-home is enabled by Smart-Licensing.

service call-home

no platform punt-keepalive disable-kernel-core

!

hostname D1

!

vrf definition Mgmt-vrf

!

address-family ipv4

exit-address-family

!

address-family ipv6

exit-address-family

!

no aaa new-model

switch 1 provision ws-c3650-24ps

!

ip routing

!

no ip domain lookup

!

login on-success log

!

license boot level ipservicesk9

!

diagnostic bootup level minimal

!

spanning-tree mode rapid-pvst

spanning-tree extend system-id

!

redundancy

mode sso

!

transceiver type all

monitoring

!

class-map match-any system-cpp-police-topology-control

description Topology control

class-map match-any system-cpp-police-sw-forward

description Sw forwarding, L2 LVX data, LOGGING

class-map match-any system-cpp-default

description Inter FED, EWLC control, EWLC data

class-map match-any system-cpp-police-sys-data

description Learning cache ovfl, High Rate App, Exception, EGR Exception, NFLSAMPLED DATA, RPF Failed

class-map match-any system-cpp-police-punt-webauth

description Punt Webauth

class-map match-any system-cpp-police-l2lvx-control

description L2 LVX control packets

class-map match-any system-cpp-police-forus

description Forus Address resolution and Forus traffic

class-map match-any system-cpp-police-multicast-end-station

description MCAST END STATION

class-map match-any system-cpp-police-multicast

description Transit Traffic and MCAST Data

class-map match-any system-cpp-police-l2-control

description L2 control

class-map match-any system-cpp-police-dot1x-auth

description DOT1X Auth

class-map match-any system-cpp-police-data

description ICMP redirect, ICMP_GEN and BROADCAST

class-map match-any system-cpp-police-stackwise–virt-control

description Stackwise Virtual

class-map match-any non-client-nrt-class

class-map match-any system-cpp-police-routing-control

description Routing control and Low Latency

class-map match-any system-cpp-police-protocol-snooping

description Protocol snooping

class-map match-any system-cpp-police-dhcp-snooping

description DHCP snooping

class-map match-any system-cpp-police-system-critical

description System Critical and Gold Pkt

!

policy-map system-cpp-policy

!

interface GigabitEthernet0/0

vrf forwarding Mgmt-vrf

no ip address

negotiation auto

!

interface GigabitEthernet1/0/1

!

interface GigabitEthernet1/0/2

!

interface GigabitEthernet1/0/3

!

interface GigabitEthernet1/0/4

!

interface GigabitEthernet1/0/5

no switchport

ip address 10.10.0.2 255.255.255.248

ip ospf dead-interval 20

ip ospf hello-interval 5

!

interface GigabitEthernet1/0/6

!

interface GigabitEthernet1/0/7

!

interface GigabitEthernet1/0/8

!

interface GigabitEthernet1/0/9

!

interface GigabitEthernet1/0/10

!

interface GigabitEthernet1/0/11

!

interface GigabitEthernet1/0/12

!

interface GigabitEthernet1/0/13

!

interface GigabitEthernet1/0/14

!

interface GigabitEthernet1/0/15

!

interface GigabitEthernet1/0/16

!

interface GigabitEthernet1/0/17

!

interface GigabitEthernet1/0/18

!

interface GigabitEthernet1/0/19

!

interface GigabitEthernet1/0/20

!

interface GigabitEthernet1/0/21

!

interface GigabitEthernet1/0/22

!

interface GigabitEthernet1/0/23

no switchport

ip address 10.10.8.1 255.255.255.0

!

interface GigabitEthernet1/0/24

no switchport

ip address 10.10.9.1 255.255.255.0

!

interface GigabitEthernet1/1/1

!

interface GigabitEthernet1/1/2

!

interface GigabitEthernet1/1/3

!

interface GigabitEthernet1/1/4

!

interface Vlan1

no ip address

!

router ospf 123

router-id 2.2.2.2

auto-cost reference-bandwidth 1000

passive-interface default

no passive-interface GigabitEthernet1/0/5

network 10.10.0.2 0.0.0.0 area 0

network 10.10.8.1 0.0.0.0 area 0

network 10.10.9.1 0.0.0.0 area 0

!

ip forward-protocol nd

ip http server

ip http secure-server

!

control-plane

service-policy input system-cpp-policy

!

line con 0

exec-timeout 0 0

logging synchronous

stopbits 1

line aux 0

stopbits 1

line vty 0 4

login

line vty 5 15

login

!

end

Switch D2

D2# show run

Building configuration…

Current configuration : 6674 bytes

!

version 16.9

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

! Call-home is enabled by Smart-Licensing.

service call-home

no platform punt-keepalive disable-kernel-core

!

hostname D2

!

vrf definition Mgmt-vrf

!

address-family ipv4

exit-address-family

!

address-family ipv6

exit-address-family

!

no aaa new-model

switch 1 provision ws-c3650-24ps

!

ip routing

!

no ip domain lookup

!

login on-success log

!

license boot level ipservicesk9

!

diagnostic bootup level minimal

!

spanning-tree mode rapid-pvst

spanning-tree extend system-id

!

redundancy

mode sso

!

transceiver type all

monitoring

!

class-map match-any system-cpp-police-topology-control

description Topology control

class-map match-any system-cpp-police-sw-forward

description Sw forwarding, L2 LVX data, LOGGING

class-map match-any system-cpp-default

description Inter FED, EWLC control, EWLC data

class-map match-any system-cpp-police-sys-data

description Learning cache ovfl, High Rate App, Exception, EGR Exception, NFLSAMPLED DATA, RPF Failed

class-map match-any system-cpp-police-punt-webauth

description Punt Webauth

class-map match-any system-cpp-police-l2lvx-control

description L2 LVX control packets

class-map match-any system-cpp-police-forus

description Forus Address resolution and Forus traffic

class-map match-any system-cpp-police-multicast-end-station

description MCAST END STATION

class-map match-any system-cpp-police-multicast

description Transit Traffic and MCAST Data

class-map match-any system-cpp-police-l2-control

description L2 control

class-map match-any system-cpp-police-dot1x-auth

description DOT1X Auth

class-map match-any system-cpp-police-data

description ICMP redirect, ICMP_GEN and BROADCAST

class-map match-any system-cpp-police-stackwise–virt-control

description Stackwise Virtual

class-map match-any non-client-nrt-class

class-map match-any system-cpp-police-routing-control

description Routing control and Low Latency

class-map match-any system-cpp-police-protocol-snooping

description Protocol snooping

class-map match-any system-cpp-police-dhcp-snooping

description DHCP snooping

class-map match-any system-cpp-police-system-critical

description System Critical and Gold Pkt

!

policy-map system-cpp-policy

!

interface GigabitEthernet0/0

vrf forwarding Mgmt-vrf

no ip address

negotiation auto

!

interface GigabitEthernet1/0/1

!

interface GigabitEthernet1/0/2

!

interface GigabitEthernet1/0/3

!

interface GigabitEthernet1/0/4

!

interface GigabitEthernet1/0/5

no switchport

ip address 10.10.0.3 255.255.255.248

ip ospf dead-interval 20

ip ospf hello-interval 5

ip ospf priority 0

!

interface GigabitEthernet1/0/6

!

interface GigabitEthernet1/0/7

!

interface GigabitEthernet1/0/8

!

interface GigabitEthernet1/0/9

!

interface GigabitEthernet1/0/10

!

interface GigabitEthernet1/0/11

!

interface GigabitEthernet1/0/12

!

interface GigabitEthernet1/0/13

!

interface GigabitEthernet1/0/14

!

interface GigabitEthernet1/0/15

!

interface GigabitEthernet1/0/16

!

interface GigabitEthernet1/0/17

!

interface GigabitEthernet1/0/18

!

interface GigabitEthernet1/0/19

!

interface GigabitEthernet1/0/20

!

interface GigabitEthernet1/0/21

!

interface GigabitEthernet1/0/22

!

interface GigabitEthernet1/0/23

no switchport

ip address 10.10.24.1 255.255.255.0

!

interface GigabitEthernet1/0/24

no switchport

ip address 10.10.25.1 255.255.255.0

!

interface GigabitEthernet1/1/1

!

interface GigabitEthernet1/1/2

!

interface GigabitEthernet1/1/3

!

interface GigabitEthernet1/1/4

!

interface Vlan1

no ip address

!

router ospf 123

router-id 3.3.3.3

auto-cost reference-bandwidth 1000

passive-interface default

no passive-interface GigabitEthernet1/0/5

network 10.10.0.0 0.0.0.7 area 0

network 10.10.24.0 0.0.0.255 area 0

network 10.10.25.0 0.0.0.255 area 0

!

ip forward-protocol nd

ip http server

ip http secure-server

!

control-plane

service-policy input system-cpp-policy

!

line con 0

exec-timeout 0 0

logging synchronous

stopbits 1

line aux 0

stopbits 1

line vty 0 4

login

line vty 5 15

login

!

end

• Recommend