H12-211 : HCIA Routing & Switching : Part 11

H12-211 : HCIA Routing & Switching : Part 11

1. Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose three)

   • The port receives only RIPv2 multicast packets.
   • The port does not receive RIPv1 broadcast packets.
   • The port does not receive RIPv2 broadcast packets.
   • The port receives only RIPv1 multicast packets.

2. When a network administrator configures STP in the network, BPDU begin to be sent by switch. Which of the following statements regarding the BPDU frame are correct?

   • A BPDU uses the IEEE 802.3 standard frame type
   • A BPDU uses the Ethernet II standard frame type
   • The BPDU frame’s control field is 3
   • The destination MAC address field of a BPDU frame is a broadcast address

3. In the case of Huawei router, the Tracert command uses UDP to encapsulate probe packets.

   • True
   • False

4. The broadcast address of the subnet 192.168.1.0/25 is 192.168.1.128.

   • True
   • False

5. A network administrator wishes to assign an IP address to a router interface G0/0/0. Which of the following IP addresses can be assigned?

   • 192.168.10.112/30
   • 237.6.1.2/24
   • 145.4.2.55/26
   • 127.3.1.4/28

6. If a network’s address is 192.168.1.0, the broadcast address of the network is 192.168.1.255.

   • True
   • False

7. In the VRP system, what are the functions of Ctrl+Z?

   • Return from the system view to the user view
   • Exit from the current view
   • Exit from the interface view
   • Exit from the console interface view
   • Return to the user view

8. In standard STP mode, which of the following ports on non-root switches forward the BPDUs with TC bits set generated by the root switch?

   • Root port
   • Backup port
   • Designated port
   • Alternate port

9. Assuming all STP enabled switches have the same bridge priority. The MAC address of switch A is 00-e0-fc-00-00-40, the MAC address of switch B is 00-e0-fc-00-00-10, the MAC address of switch C is 00-e0-fc-00-00-20, and the MAC address of switch D is 00-e0-fc-00-00-80.

   Which switch will be elected as the root switch?

   • Switch A
   • Switch B
   • Switch C
   • Switch D

10. As specified by the RSTP protocol, when a root port fails, which type of port will function as a new root port and enters the forwarding state without any delay?

    • Forwarding Port
    • Alternate Port
    • Backup Port
    • Edge Port

11. In STP, the priority of the STP root switch ranges from 0 to 65536.

    • True
    • False

12. Refer to the graphic. Which statements correctly explains the forwarding behavior between RTA and RTE? (Choose all that apply)

    

    • When the network uses OSPF, data will be forwarded along the path via S1/0/0
    • When the network uses RIPv2, data will be forwarded along the path via S1/0/0
    • When the network uses OSPF, data will be forwarded along the path from via E0/0/1
    • When the network uses RIPv2, data will be forwarded along the path via S2/0/0

13. Refer to the graphic. RTA and RTB are running RIPv1. RTA has advertised 10.0.0.0 and 192.168.1.0 to the RIP network. Which routes will exist in the IP routing table of RTB? (Choose all that apply)

    

    •  10.0.0.0/8
    • 192.168.1.1/32
    • 10.1.12.1/32
    • 192.168.1.0/24

14. Which of the following configurations regarding static route are correct? (Choose all that apply)

    • ip route-static 129.1.0.0 16 serial 0
    • ip route-static 10.0.0.2 16 129.1.0.0
    • ip route-static 129.1.0.0 16 10.0.0.2
    • ip route-static 129.1.0.0.255.255.0.0 10.0.0.2

15. Refer to the graphic. An administrator has configured RIPv2 in the two routers. What will happen after configuring the following commands: (Choose all that apply)

    

    •  RTA will have the route learned from the RTB
    • RTB will have the route learned from the RTA
    • RTA will have no neighbor relationship with RTB
    • RTB will have no neighbor relationship with RTA

16. Refer to the graphic. OSPF is used on four routers that are in the same area and on the same network segment. In this scenario, OSPF selects one DR and multiple BDRs to ensure backup.

    

    • True
    • False

17. On Huawei devices, you can use the undo summary command to prohibit automatic route summarization of RIPv2.

    • True
    • False

18. Which of the following configurations regarding default route configuration is correct?

    • [Quidway] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1
    • [Quidway] ip route-static 0.0.0.0 255.255.255.255 172.16.2.1
    • [Quidway-GigabitEthernet0/0/1] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1
    • [Quidway] ip route static 0.0.0.0 0.0.0.0 172.16.2.1

19. Which of the following WLAN standards support operation in the 5GHz range? (Choose all that apply)

    • 802.11a
    • 802.11b
    • 802.11g
    • 802.11n

20. On Huawei switches, you can run the vlan batch command to create multiple VLANs in batches.

    • True
    • False